KEY TAKEAWAYS
- Mixed fleets are the hardest fleets to track for fuel: each makes reports fuel data differently, tanks vary in shape and size, and older vehicles share less data than newer ones.
- Fitting an aftermarket fuel sensor to every tank in a mixed fleet is slow and costly; reading the fuel data each vehicle already produces scales faster.
- Intangles connect through each vehicle’s OBD port with no modifications and apply patented algorithms to the fuel sensors the vehicle already has, so no new hardware goes into the tank.
- Intangles’ US Patent No. 11,566,575 estimates fuel levels between the coarse steps a factory fuel sender reports by combining fuel-level readings with fuel-consumption data.
- US on-highway diesel reached $6.529 a gallon in the week of September 21, 2026, the highest weekly average in EIA records dating back to 1994.
Most commercial fleets aren’t uniform. A typical operation runs heavy trucks beside medium-duty vans and new models beside ten-year-old ones, often from half a dozen manufacturers. Fuel tracking that reads well on one model can be unreliable on the next.
That gap is getting more expensive. US on-highway diesel peaked at $6.529 a gallon in the week of September 21, 2026, and was still $6.199 on October 5, about $2.49 more than a year earlier, according to the US Energy Information Administration. Even in 2025, when diesel stayed under $4 a gallon, fuel cost carriers 48.2 cents a mile, according to the American Transportation Research Institute’s 2026 operational costs update.
Every gallon a mixed fleet can’t account for now costs more than it did at any point before September 2026.
In this blog, you will learn why fuel tracking is harder in mixed fleets, what a fuel tracking device needs to do across different makes and models, how Intangles tracks fuel on every vehicle, how to tell theft from waste, and how to test it on your own fleet before rolling it out.
Why is fuel tracking harder in mixed fleets?
Because no two vehicle types report fuel the same way. Each make, tank and model year needs its own reading, and a system tuned for one vehicle can misread the next.
| Challenge | Why it matters |
| Different makes and models | Each manufacturer reports fuel data differently, so one device can read well on one model and poorly on another |
| Different tank shapes and sizes | The same change in fuel height means different volumes in different tanks, so readings must be calibrated to each one |
| Older and newer vehicles | Older vehicles often share less data, which leaves gaps if a system only works well on newer models |
| Different duty cycles | Long-haul, stop-start and off-road vehicles burn fuel differently, so one fleet-wide benchmark hides waste |
| Several systems at once | Many mixed fleets end up with a manufacturer portal for one brand, a tracker for another and fuel cards on top, with no single view |
The result is predictable. Some vehicles are tracked well, some badly, and the losses hide in the gaps.
For how different fuel monitoring devices work and what makes them accurate, see fuel monitoring devices compared.
What does a mixed fleet need from a fuel tracking device?
Coverage of every vehicle without tank work, a separate baseline for each vehicle, and one place to see it all.
| Requirement | Why |
| Works across every make and model | So no vehicle becomes a blind spot |
| No tank work on every vehicle | Drilling and fitting sensors across a mixed fleet takes vehicles off the road and adds cost per vehicle |
| Per-vehicle baselines | Each vehicle is compared with its own expected consumption, not a fleet average |
| Clear separation of theft and waste | High consumption can mean theft, poor driving or a mechanical fault, and each needs a different fix |
| One view | Every vehicle and every fuel event sits in the same platform |
| Proof on your own vehicles | Accuracy claims only matter if they hold on your fleet |
The practical test is simple. If a device can’t meet all six on your oldest vehicle, it can’t meet them on your fleet.
How does Intangles track fuel across a mixed fleet?
Instead of adding a sensor to every tank, Intangles reads the fuel data each vehicle already produces and makes it more precise.
One connection, no tank modifications
The InGenious device connects through each vehicle’s OBD port with no modifications. There’s no drilling and no new sensor in the tank.
Patented algorithms on existing sensors
Intangles’ fuel monitoring applies patented algorithms to the OEM-installed fuel sensors the vehicle already has. Factory fuel senders are built to drive a dashboard gauge, so they report fuel in coarse, discrete steps, and fuel sloshing in the tank disturbs their readings. Intangles’ US patent for sub-resolution fuel measurement combines those level readings with fuel-injection data to estimate the fuel level between the steps. That sharpens the numbers fleets rely on for consumption, refills and losses.
A digital twin of every vehicle
Intangles is a digital twin company. It models how each vehicle should be running and compares that with how it actually runs. For fuel, that means each vehicle is judged against its own expected consumption, whatever its make, age or duty cycle.
One platform
A consumption record for every vehicle, and a time, place and volume for every fuel loss.
What Intangles shows | Why it matters |
How much fuel each vehicle is using, at all times | Every vehicle has its own consumption record, whatever its make |
Where, when and how much fuel was lost | Drops are tied to a time and place, so they can be investigated while the evidence is fresh |
Consumption against each vehicle’s expected baseline | A truck burning more than it should is visible, even if no fuel was stolen |
Where every vehicle was when a fuel event happened | Location tracking shows whether a drop happened at a depot, a pump or somewhere unexpected |
Driving behavior behind high consumption | Driver behavior monitoring with DriveIQ flags 20+ behavioral exceptions, including idling and harsh driving |
Engine faults that raise consumption | Predictive health monitoring flags developing faults before diagnostic trouble codes appear |
Theft, waste or a failing part: how do you tell them apart?
By checking each fuel anomaly against location, driver behavior and vehicle health. In a mixed fleet, high fuel use has many possible causes, and treating them all as theft wastes time and damages trust with drivers.
| Cause | What it looks like | What fixes it |
| Theft | A drop in fuel level, often while parked, at a specific time and place | Investigation and tighter controls on refueling locations and fuel cards |
| Idling | Fuel burned with the vehicle stationary | Driver coaching and idle policies; see what idling is |
| Driving habits | Higher consumption on the same route than other drivers | Coaching using driver behavior scores |
| Mechanical faults | Consumption creeping up over weeks, sometimes with engine alerts | Planned repair before it becomes a breakdown |
This is where connected data earns its keep. Because Intangles links fuel data with location, driver behavior and vehicle health, each anomaly can be checked against all three, so the team fixes the real cause.
How do you roll out fuel tracking across a mixed fleet?
Start small, test on every vehicle type, and check the numbers against your own records before scaling.
- List every vehicle by make, model, year and fuel type.
- Pilot on a mix that covers every make and model year in the fleet, not just the newest vehicles.
- Test accuracy with measured fills. Fill to full at a trusted pump and compare the dispensed volume with the refill the system reports.
- Run a controlled drain on one parked vehicle and check how quickly and accurately it’s flagged.
- Review a month of data against fuel card records and your own baseline before scaling.
For a full rollout plan after the pilot, see the 90-day fleet software implementation plan. For the mistakes to avoid once monitoring is live, see the 5 fuel monitoring mistakes costing your fleet.
Why do fleets choose Intangles for mixed-fleet fuel tracking?
Because one connection covers every vehicle and every fuel question. Intangles is a digital twin company with 500,000+ vehicles on its platform. The same OBD connection that tracks fuel also powers predictive health monitoring and DriveIQ driver behavior monitoring, so one device serves the whole fleet across trucking, construction and waste management operations.
Discover how Intangles’ fuel monitoring can track fuel on every make and model in your mixed fleet, without fitting new hardware in every tank.
KNOW MORE
Frequently Asked Questions
What is the best way to track fuel in a mixed fleet?
The best way is a system that works across every make and model without separate hardware in every tank, compares each vehicle with its own expected consumption, and shows every fuel event in one view. Test it on a sample of every vehicle type in your fleet before rolling it out.
Do I need to install fuel sensors in every vehicle?
Not with Intangles. Its device connects through the OBD port with no modifications and applies patented algorithms to the fuel sensors the vehicle already has, so there’s no drilling and no new tank hardware. Software, hardware and algorithms work together as one integrated solution.
How does Intangles track fuel across different makes and models?
Intangles reads each vehicle’s existing fuel data through the OBD port and processes it with patented algorithms, including a US-patented method that estimates fuel levels between the coarse steps a factory fuel sender reports. Its digital twin then compares each vehicle’s actual consumption with what it should be burning, so every vehicle is judged against its own baseline, not a fleet average.
Can fuel tracking tell theft apart from poor driving or a mechanical problem?
Yes, when fuel data is combined with location, driver behavior and vehicle health data. A drop while parked at an unexpected location points to theft, higher consumption on the same route points to driving habits, and a gradual increase alongside engine alerts points to a mechanical fault, such as fuel rail pressure problems.
How much does fuel cost a trucking fleet per mile?
Fuel cost US and Canadian for-hire carriers an average of 48.2 cents a mile in 2025, out of a total operating cost of $2.336 a mile, according to ATRI’s 2026 operational costs update. Diesel averaged under $4 a gallon through 2025 but has been above $6 since mid-September 2026, so fleets should expect a higher per-mile fuel figure this year. EIA’s October 2026 Short-Term Energy Outlook expects diesel to average $5.19 a gallon in 2026 and about $4.49 in 2027. To estimate what fuel waste costs your own fleet, use the fleet savings calculator.
How do I check if my vehicles are supported?
List your vehicles by make, model, year and fuel type, and ask for coverage to be confirmed for each one before signing. You can contact Intangles with that list to check coverage. A pilot that includes every make and model year in the fleet is the best way to confirm it in practice.
How can I test the accuracy of a fuel tracking device?
Fill a vehicle to full at a pump you trust and compare the dispensed volume with the refill the system reports. Retail fuel pumps in the US are inspected by state weights and measures officials against NIST Handbook 44 accuracy tolerances, so a recently inspected pump is a reliable reference. Then remove a measured amount from a parked vehicle and check how quickly and accurately the system flags it, and repeat the test across each vehicle type in your fleet.
We’re looking forward to meeting you